Ovatko tietokoneventtiilit aina 100%, ellei sanonut muuten?

Sisällysluettelo:

Ovatko tietokoneventtiilit aina 100%, ellei sanonut muuten?
Ovatko tietokoneventtiilit aina 100%, ellei sanonut muuten?
Anonim
Olipa kannettavia tietokoneita, pöytätietokoneita tai jopa pelikonsoleja, olemme kaikki kuulleet järjestelmän fanien whir taustalla. Kuinka tarkasti kaikki nämä pienet jäähdytyspuhaltimet tietävät, milloin ne pyörivät ylös, alas ja muuten heikentävät ilman määrää?
Olipa kannettavia tietokoneita, pöytätietokoneita tai jopa pelikonsoleja, olemme kaikki kuulleet järjestelmän fanien whir taustalla. Kuinka tarkasti kaikki nämä pienet jäähdytyspuhaltimet tietävät, milloin ne pyörivät ylös, alas ja muuten heikentävät ilman määrää?

Tämänpäiväinen kysymys- ja vastaus-istunto tulee meille Hyvinkään, Super-käyttäjän, Stack Exchange-jaosta, joka on yhteisöllinen Q & A-sivustojen ryhmittely.

Kysymys

SuperUser-lukija darkAsPitch ihmeitä:

What happens if I do not plug it into the motherboard and it does not have a switch?

I have seen fans before with an “off/low/high” switch that allows you to manually set their speed.

I have seen fans that plug into the motherboard and are controlled by the OS.

I am curious… what does a fan do by default when plugged into a PSU? Does it run at 100% unless otherwise told to go slower? This is what I would expect…

Niin miten he työskentelevät? Täysi poraus ellei toisin ole määrätty?

Vastaus

SuperUser-avustaja Journeyman Geek tarjoaa seuraavanlaisen näkemyksen:

Well, kind of. Fan speed control is done by varying voltage or through Pulse Width Modulation (using a constant voltage and cutting it up into pulses to vary speed). If you’re plugged into a motherboard, that’s what it does. If it has 3 wires, the third wire tells the motherboard what’s the speed the fan is running as. If you have a 4th wire, fan speed control is done via PWM rather than voltage control.

You can plug in a 2 wire fan to a 3 or 4 wire connector (though you lose speed feed back), and a 3 wire to a 4 wire connector (where you lose PWM control). You can also use a fan controller to control speeds.

Else, assuming the power source is unaware it’s a fan (as it would be connected through molex for example), and is at a fixed voltage, yes, it goes at full speed all the time.

Työntekijä Hyperslug korostaa poikkeusten merkitystä:

Like the other guys said, pretty much yes, but I can think of 3 exceptions:

1. A few fans have a built in thermistor that will adjust speed depending on temperature.

2. PSU’s with specially marked Fan-Only PSU connectors (Antec TruePower 550W) can adjust the speed of the fan:

3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.
3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.

Ja siellä sinulla on se: ulkoisen valvonnan ulkopuolella jonkin mekanismin kautta (olkoon se emolevyn syöttö, tapaus lämpömittari tai älykäs virtalähde), puhaltimet toimivat suurimmalla nopeudella, jonka virtalähde sallii.

Onko jokin asia lisättävä selitykseen? Kuulkaa kommentit. Haluatko lukea lisää vastauksia muilta tech-tajuilta Stack Exchange-käyttäjiltä? Katso koko keskusteluketju täältä.

Suositeltava: