Tämän päivän kysymys- ja vastausistunto tulee meihin SuperUserin hyväksi - Stack Exchangein alaosasto, joka on yhteisöllinen Q & A-sivustojen ryhmittely.
Kuva ystävällisesti Xiao Zong Zongista (小宗 宗 - Flickr).
Kysymys
SuperUser-lukija Xavierjazz haluaa tietää, tarvitaanko USB 3.0 -liitännät USB 3.0 -kaapeleita, jotta niiden täysi nopeuspotentiaali saavutetaan:
Do USB 3.0 connections require USB 3.0 cords to reach USB 3.0 speeds? Will any USB cord support any USB 3.0 device?
Onko USB 3.0 -liitännät edellyttävät USB 3.0 -kaapeleita voidakseen saavuttaa täyden nopeuden potentiaalinsa?
Vastaus
SuperUser-avustajat Steven ja fixer1234 ovat meille vastauksen. Ensin, Steven:
A USB 3.0 cable is required for USB 3.0 speeds, but any USB cord will make a connection.
Source 1: USB [Wikipedia]
SuperSpeed (USB 3.0) is supported only by USB 3.0 and newer interfaces, and requires a connector and cable with extra pins and wires, usually distinguishable by the blue inserts in connectors.
Source 2: USB 3.0 Super Speeds [USRobotics]
USB 3.0 cables can be used with 2.0 devices and ports if the connector types fit (no B Male or B Micro connectors), but the transfer rate will fall back to 2.0.
Source 3: Are USB 3.0 cables different? [UserBenchmark]
To get USB 3.0 speeds, you need special USB 3.0 cables. Yes, USB 3.0 cables are different. Even though you can connect a USB 3.0 device via a USB 2.0 cable, in order to achieve full USB 3.0 speeds you need to rewire any existing cabling. USB 3.0 cables have more internal wires, are usually blue, and are noticeably thicker than the old USB 2.0 cables. We figured this out the hard way during the USB flash drive group test.
Jälkeen answerer1234: n vastaus:
You cannot achieve USB 3.0 speeds without a USB 3.0 cable. However, speed is not the only issue.
A USB 2.0 cable will work (at USB 2.0 speeds), for some, but not all, USB 3.0 devices. There are at least three important differences in cable construction between the two standards.
Related to Speed:
USB 3.0 cables have nine internal conductors versus four in USB 2.0 cables.
Four of the nine internal conductors match the USB 2.0 configuration (two are for power and two are for signal). Connecting a USB 3.0 device with a USB 2.0 cable uses those conductors and operates like a USB 2.0 device.
The other five are signal conductors which are used for the communication method that provides USB 3.0 super speed. A good general description can be found here: USB 3.0 [Wikipedia]
USB 3.0 cables have a limit of three meters versus the USB 2.0 limit of five meters.
(Note that this is a practical limit.) The cable can be any length as long as it meets all of the electrical requirements in the specification. The three meter limit is based on maximum allowable losses using the largest recommended wire size so that the cable is flexible. Specs Document [Zip File – USB.org]
Related to Power:
A USB 2.0 cable may not be adequate for a high current USB 3.0 device.
Some USB 3.0 devices draw more power than USB 2.0 devices. The power conductors in USB 3.0 cables need to be able to carry 900 mA versus 500 mA for USB 2.0 cables.
Additional information on USB 3.0 versus 2.0 can be found here: USB 2.0 vs. USB 3.0 [Diffen]
Onko jokin asia lisättävä selitykseen? Kuulkaa kommentit. Haluatko lukea lisää vastauksia muilta tech-tajuilta Stack Exchange-käyttäjiltä? Katso koko keskusteluketju täältä.
